About DCT4 Direct
Software:
- Works on Window XP
- Future updates and support
- Real USB data transfer between PC and Phone
- Best Quality phone Cables and Software
How its works:
On all Nokia DCT4 phones the important security data
for the IMEI and ESN is stored on a special, note
rewritable chip inside the phone: the UEM chip. This
chips characteristic is that it is only one time
programmable (OTP) and that the data inside cannot be
rewritten. Because of this, until now it was only
possible, to change the IMEI/ESN if you change this
UEM chip. Since this task requires a lot of time and
effort, alot of customers were looking for a easier
solution, without the need to open the phone and
change some components inside. And after some time
finally somebody created a tool that was able to do
all that operations without changing the UEM chip: the
DCT4 DIRECT Box. THis software is using a special
techic in order to make it possible to change the
IMEI/ESN without changing any data on the UEM chip it
self. This task is done by editing the MCU Firmware
inside the phone and writing the desired IMEI/ESN data
to the FLASH, not to the UEM chip, this procedure is
also known as FLASH PATCHING. After the phone has been
updated with the patched flash data by the DCT4 DIRECT
BOX the phone will have the new IMEI/ESN number and
all simlock data rebuild as well. This might sound a
little bit complicated now, but in fact the user is
not affected in any way by this procedure. All the
user need to do is to type the desired IMEI/ESN number
into a field and then just press one button for
starting the IMEI/ESN change. IMEI/ESN change on DCT4
phones is really easy now.
Support phone models:
DCT4 Direct (v1.0.0.32):
-
NHM-7 - 8310, v 6.20
-
RH-19 - 3100, v 5.91
-
NHL-6 - 6800, v 3.14
-
RH-9 - 3510i, v 5.35
-
RM-17 - 7260, v 3.36
-
NEM-1 - 3300, v 4.62
-
NPL-2 - 6100, v 5.80
-
RH-23 - 7200, v 4.26
-
NHL-4J - 7250, v 3.62
-
NPE-4 - 6310, v 5.10
-
NHL-4 - 7210, v 5.63
-
NPL-1 - 6310i, v 7.00
-
RH-37 - 3220, v 3.60
-
RM-37 - 6610i, v 4.10
-
NHM-8 - 3510, v 5.02
-
RH-30 - 3200, v 5.29
-
NHL-4JX - 7250i, v
5.30
-
NKC-1 - 2270, v 9.07
-
NPC-1 - 3320, v 4.00
-
NPW-1PA - 3361*, v
3.06
-
RH-17R - 2280, v
F175V0500.nep
-
DTE-1 - D211*, v 4.01
-
RH-18 - 1100*, v 5.62
-
NPM-10 - 3595, v 8.18
-
NKC-1 - 1220, v 9.07
-
NPD-1AW - 3585, v
B100V0557.nep
-
RH-44 - 3586, v
D100V0112.nep
-
RH-3 - 2285, v
G101V0801.nep
-
NPM-8 - 3590, v 7.64
-
RM-12 - 7710, v
Vp2.200
-
RA-2 - 9500, v 3.35.2
-
RH-38 - 1100a*, v
5.62
-
NHL-9 - 6820a, V 4.25
-
RAE-6 - 9300, v 3.06
-
RH-48 - 3105, v
J175V0300.nep
-
NPL-3 - 6200, v 4.22
-
RH-27 - 6225, v
H190V0800.nep
-
RH-50 - 3100b, v 4.03
Note:
The Supported Phones above marked with Star (*)
sign do not operate properly with this version. Do not
use them. In case you do and have a dead phone, just
reflash the MCU to repair it(1100 - MCU+PPM).
IMPORTANT:
-
Please note that the
DCT4 DIRECT BOX cannot work with phones that:
- Have bad UEM data (30 sec off problem)
- Don't have any UEM data at all (??????????????
IMEI/ESN)
- Have SOftware/Hardware problems
-
Please always check
if phone is in full working condition before
starting the IMEI/ESN change procedure.
-
If you want to bring
the phone back to it's original state, then you
only need to flash the phone with original MCU
software. After MUC software update the patch will
be erased and the phone will operate as before.
Package
Contains
